Be careful not to touch the bulb part of the new headlight. Almost like you put a whole new front end on your Jetta. If not, you may want to take it to a mechanic. Position the headlight up to the fender. Order your new headlights from AutoZone and rely on trustworthy advice from our knowledgeable staff whenever you visit your local store. When headlight is back in place, slide the arm back into place and you are done.
OnceI did that I was able to properly seat the bulb note: Aligning thethree little grooves is very important. You might want to have someone helping you at this point, as if you drop the headlight you could seriously damage it. You'll see a black ring that obstructs the removal ofthe lightbulb. Takeyour time, do not be frustrated by the lack of space to work in. Once you move the handle a little, have someone else try sliding the light out while you keep trying to move the handle. Just don't force anything too hard and you should be okay. If you do get the new bulb dirty, wipe it clean with an alcohol moistened paper towel.
Then up in there, the T27 bolt and then on this side, there is the last T27 bolt. Once the screws are removed pull the plastic piece straight up. Takes about 50 seconds to do. I have a Toyota Tacoma pick-up and the headlights were beginning to oxidize pretty bad. Next the clasp and metal strap you will notice the lever that expels the light assembly. Yes, you can fix this at home, but make sure it isn't cold causes the plastic to be brittle and that you take your time.
To remove there are three screws. Put the spring clip back on and make sure the ends of the clip are in securely. Now, you want to put the bottom of your grill in first, then you want to hold these, keep them like that. Take off the plastic cover to that bulb's housing. With the old bulb you can just pull it out without a care in the world, besides not damaging the assembly. Put the socket back in its chamber. When the headlight is pulled from the fender, disconnect the wire harness.
After sliding the arm the full length of the channel, carefully pry the headlight from the fender. Also pull the liver up and out toward the light. An old screw driver or a small pry bar can be used to lift the wire away from the headlight plate cover, making it easier to unclip the wire. Changing both headlight bulbs on your Jetta at the same time will allow both bulbs to have the same intensity and prevent the new headlight bulb from appearing brighter than the bulb on the opposite side. Hopefully, none of you New Beetle owners have had to, or need to, replace an entire headlight assembly read ï¿½ expensive! It just attaches with basically a couple of tabs right here.
Answer Open the hood and look for the black 'sleeve' that holds the headlight. Final note is that the main headlights are the outboard ones and the fog lights the inner ones. It should twist about quarter turn and then pull out. The headlight is in a long, plastic tube. Correct Item Guaranteed If you receive an incorrect item from us, we will immediately pay for return shipment and send you the correct item. There are some white plastic pegs pointing inward towards the socket. In case the headlight assembly needs to be replaced, just pop the hood, and disconnect the connector that can be found behind the headlight assembly.
If you do the oil from your fingers will make a hot spot on the bulb and it will burn out quikly. Pull the rubber dust cap off the rear of the high beam bulb and set it aside in a safe place. We found this solution online so I share it with you!! As you have found out, these are totally different in concept than the old Beetle cousins. All bulbs have this O-ring but the Hella model I had was justtoo big. The company that is here for you, on the Internet and in person.
By the way you pull up! Some running lights come with these brackets in them just to keep things held together during shipping. Put the new one in in reverse order, being careful not to touch the glass or force it. Try to avoid touching the glass part of the new halogen bulb with your fingers or anything greasy in the engine bay. If you break the square tab out, like I did you can secure the lever in place after replacing the bulb by installing a small sheet metal screw next to the lever to lock it place. This is the part that should get into the lighting unit first. This information can be found in your ownerï¿½s manual or the Bentley manual for the New Beetle.